Product Overview
A 25.6 V, 60 Ah lithium iron phosphate pack — ordered as a 24V LiFePO4 battery — that stores 1,536 Wh in a sealed ABS case with bolted terminal posts. Cells inside are matched for capacity and internal resistance and managed by a protection board that watches voltage, current and temperature.
Its place is the middle of the 24 V range. Where a 10 Ah pack suits a scooter and a 100 Ah pack suits a large RV bank, 60 Ah covers equipment that runs for hours rather than minutes: solar lighting and small storage systems, backup cabinets, golf carts, light electric vehicles and the DC side of remote installations.
The chemistry is why buyers move here from lead-acid. A rechargeable lithium battery at this capacity holds a steady voltage through the discharge, accepts charge without a long absorption phase and needs no watering or equalising. Depth of discharge is not the constraint it is on a flooded block, so the same 60 Ah nameplate gives more usable energy in practice.
Cycle life is rated at 2,000 cycles or more down to 80% of initial capacity. At one cycle a day that is more than five years of daily service before the pack reaches that point, and most lighting, backup and traction duties cycle less often than that.
Production, Testing and Quality Control
- Electrode production. Active material mixing, coating, rolling and slitting run on automatic lines; the electrode is then wound and seated in the cell shell.
- Cell assembly. Tab welding, electrolyte injection and laser welding of the cap finish the cell, and each joint is checked before the cell moves on.
- Formation and capacity sorting. Every cell intended for this lithium iron phosphate battery is formed and then graded on measured capacity, so the cells that end up in the same pack start from the same baseline.
- Three-cycle test. All cells run three full charge and discharge cycles before release — nothing is sampled, everything is cycled.
- Final inspection. Finished packs are checked 100% for appearance, voltage, capacity, internal resistance and dimensions before packing.
- Certification. CE and RoHS certification apply to this 24V LiFePO4 battery; ask your sales contact for the current certificate set and for the transport documents your forwarder needs for the destination market.
Case, Terminals and Installation Fit
- Footprint of 335 x 175 x 280 mm (L x W x H). Measure the tray, then add clearance above the case for the top handle and for the cable lugs — the 280 mm height is what usually decides whether a side-access battery box will take it.
- About 17.5 kg in the hand. Roughly 70% lighter than the lead-acid block of similar nominal voltage it typically replaces, which matters on a pole, in a vehicle or in a cabinet that has to be lifted into place. The flat case sides accept a standard hold-down strap.
- Moulded ABS housing. Impact resistant, electrically insulating, and it does not corrode in a compartment that has previously held a venting lead-acid block.
- Terminal type: ABS. Tell us the bolt and lug size you plan to use when you order, so the terminal hardware supplied matches your cable ends.
- Polarity and isolation. Bring the positive and negative leads to the marked posts, fit a breaker or isolator on the positive side, and meter the polarity before the first connection.
- Charger profile. Set the charger or solar controller to stop at 29.6 V before the first charge. A profile left over from lead-acid will either leave this 24V LiFePO4 battery short of full or hold it above the voltage it wants.
- First charge. Bring the pack to full before putting it under load. Packs travel at a partial state of charge, and a full charge lets the protection board level the cell groups.
- Where to mount it. No IP rating is stated for this rechargeable lithium battery, so plan on a dry, ventilated enclosure rather than an exposed pole-top position, and keep the case away from heat sources and standing water.
Operating Window and Storage
This lithium iron phosphate battery charges from 0 °C to 45 °C and discharges from -20 °C to 60 °C. The charge floor matters more than the headline figure: on a freezing morning a solar controller will happily push current into a cold pack, so site the battery where it warms with the day, or use a controller that holds off charging until the pack is above zero.
The discharge window covers most outdoor work — -20 °C for cold stores and winter roadside cabinets, 60 °C for a sun-exposed enclosure on a hot afternoon. Treat the ends of that range as survival limits rather than working conditions; a pack that lives permanently at the top of the window will age faster than one that does not.
Storage is graded by temperature: up to 12 months at -20 °C to 25 °C, three months at -20 °C to 35 °C and one month at -20 °C to 45 °C. Read that as a stock-rotation instruction. A summer container or an unshaded warehouse counts, so pull stock forward rather than leaving packs in a hot corner for a season.
A rechargeable lithium battery that sits for more than a few weeks should be kept part-charged rather than full or flat, stored in a dry place, and topped up before it goes into service. A pack that has sat in storage for months will want a full charge before you rely on it.
Applications and Equipment Fit
- Solar street and billboard lighting. A 24 V buffer that carries a lighting head and controller through the night, sized so the pack is not flattened every evening in winter. Backup power and UPS. Telecom cabinets, access control panels and emergency lighting keep a lithium battery charged and idle for most of its life; when mains drops, the pack takes the load immediately and needs none of the watering a flooded block does. RV, camper and marine house banks. Lights, pumps, fans and a compressor fridge on a 24 V DC bus, in a pack light enough that payload and trim change less than they do with a lead bank. Golf carts, sightseeing vehicles and AGVs. Traction duty inside the 60 A continuous rating, with short start-up surges absorbed by the peak rating rather than tripping protection. Outdoor and garden equipment. Electric sprayers, garden tools and portable outdoor power draws — a rechargeable lithium iron phosphate battery that holds its charge between jobs and needs no topping up with water. Portable audio and site PA. Outdoor PA systems and job-site speakers that need a stable 24 V rail for an evening without a mains feed.
Electrical and Performance Specifications
| Model No. | TWE-LF24V60AH LiFePO4 battery |
| Nominal Voltage | 25.6 V |
| Nominal Capacity | 60 Ah, standard discharge at 0.2C after standard charge |
| Energy | 1,536 Wh |
| Cycle Life | ≥2,000 cycles to ≥80% of initial capacity |
| Charge Cut-off Voltage | 29.6 V |
| Discharge Cut-off Voltage | 18.4 V (20 V recommended) |
| Standard Charge Current | 12 A |
| Max Charge Current | 30 A |
| Standard Discharge Current | 12 A |
| Max Continuous Discharge Current | 60 A |
| Peak Discharge Current | 120 A for ≤5 s |
| Internal Resistance | ≤40 mΩ |
Protection and BMS
| Protection | What It Does |
| Over charge | Charging stops when a cell group reaches its upper voltage limit |
| Over discharge | Output is disconnected before the pack is drained past the discharge cut-off |
| Over current | Current is limited when a load pulls more than the pack is rated for |
| Over voltage | Charge voltage above the safe level for the string is blocked |
| Short circuit | The output is isolated if terminals or cabling short |
| Cell protection | Individual cell groups are monitored, not only the pack total |
| Temperature protection | Charging or discharging stops when the pack runs outside its temperature window |
Ordering and Custom Requirements
- Send the application details — nominal voltage, the continuous and peak current your load draws, and the space the case has to fit — so we can confirm the standard pack against your equipment.
- Agree the electrical interface. Terminal hardware, cable lug size and the charge profile your charger or solar controller will use all go on the order, so the pack arrives matching your wiring.
- Settle the build. If the standard 60 Ah pack does not suit, we build a custom lithium battery to your drawing — case size, terminal arrangement, capacity and protection settings are agreed before production starts.
- Confirm commercial terms with your sales contact: quantity, packing, lead time and shipping, together with the destination market so the right documents travel with the consignment.
- Confirm the after-sales terms. The warranty for this model runs to one year; ask your sales contact to confirm the exact terms and the claim route that apply to your order.
- Sign off before the run. If the pack goes into equipment you manufacture, ask about a pre-production unit to approve the terminals, clearance and charge profile before the full batch.
Scale & Supply Capability
Topwell Power is a lithium battery manufacturer, not a trading house. Our range runs from compact packs to large storage systems, so buyers can consolidate several lines behind one specification standard and one set of shipping documents. OEM and private-label work is routine: your label, case marking, terminal choice, capacity and packing configuration. Capacities and enclosures are customised per project, samples are available before a production run, and shipments go out with the transport documentation freight forwarders ask for. Send your target specification and volume, and we will confirm lead time, packing and pricing for that order.
FAQ
Can this pack replace the lead-acid block in a 24 V system?
In most 24 V DC systems yes, but the charging arrangement has to change with it. A LiFePO4 battery needs a charger or solar controller set to the pack's cut-off rather than a lead-acid profile, which either stops short of full or holds the pack too high. Check the bay as well — the case is a different shape and considerably lighter than a flooded block, so the hold-down needs attention.
Can it handle the start-up surge from a motor or inverter?
The protection board allows short surges within the peak rating and sustained draw within the continuous rating, so size the inverter or motor controller to the continuous figure and keep start-up surges brief. If your equipment pulls close to the continuous rating for minutes at a time, take a larger pack in the same 24 V family rather than running this one at its ceiling.
Does this model offer Bluetooth or app monitoring?
No. This model is a standard rechargeable lithium battery pack with an internal protection board that handles the limits itself. Monitoring is offered on other packs in our 24 V range — tell your sales contact if Bluetooth or app visibility is a requirement and they will point you to the right model.
Can the pack be mounted outdoors?
The ABS case is sealed and impact resistant, but no IP rating is stated for this model, so this lithium battery belongs in a dry, ventilated enclosure rather than bolted to an exposed pole. If your installation is wet or wash-down, ask about a weather-rated pack instead of leaving this one exposed.
Can you supply a custom lithium battery with different dimensions or terminals?
Yes. Send the drawing or the key dimensions, the voltage and capacity you need, the terminal or connector arrangement and the protection settings your application requires. We agree those details before production and, for equipment you manufacture, a pre-production unit can be approved before the full batch runs.
Is 60 Ah the right size, or should I look at another pack?
The 60 Ah sits between the compact 10 Ah pack used on scooters and the 100 Ah deep-cycle pack used for long RV, marine and solar runs. It suits equipment drawing tens of amps for hours with a bay that will not take a larger case; if your load runs a big inverter all evening, step up to the 100 Ah model.