24V 100Ah LiFePO4 Battery for RV/Camper, Solar, Marine

Item No.: TWE0586
Brand: TWE
Nominal Voltage: 25.6V
Nominal Capacity: 100Ah
Max Dimensions: 522*238*220
Certificate: CE, ROHS, MSDS, UN38.3, etc.
Warranty: 1 year
Description Brand Introduction Review
Description

Product Overview

The 25.6V 100Ah pack is a LiFePO4 battery for vehicles, boats and off-grid systems that need steady 24V power day after day. It feeds house circuits, inverters and DC equipment directly, without the watering, venting or slow recharge acceptance of a lead-acid bank. The case is ABS+PC with threaded terminal posts, and the assembly arrives as one complete block rather than a set of cells you wire together yourself.

CB test certificate for a lithium-ion polymer battery

Weight is usually what decides the upgrade. This lithium battery can be lifted and set into a locker by one person, and it runs roughly 70% lighter than the lead-acid bank it replaces — which also takes load off a vehicle's gross weight and off a boat's trim.

24V 100Ah LiFePO4 Battery for RV/Camper, Solar, Marine

Dimensions are marked customized on this model, and that reflects how these packs are actually ordered. A custom lithium battery build lets the case match the bay you have and the terminals face the cable run you already own, instead of forcing your wiring to fit a fixed shell.

24V 100Ah LiFePO4 Battery for RV/Camper, Solar, Marine

Treat it as a deep cycle battery and it behaves the way the duty demands: run down, recharged, run down again, season after season, without the capacity walk-down a lead-acid set shows after a few hundred cycles. That cycling behaviour, rather than the label on the case, is what decides whether the pack still holds its rating in year five.

A residential roof fitted with a solar panel array
Solar street lights mounted along a roadside
Shenzhen BST Technology Co

Battery Management & Safety

  • Seven protections on one board. Over-charge, over-discharge, over-current, over-voltage, short circuit, cell protection and temperature protection all sit inside the case, so a fault trips at the management board rather than travelling down your cable run.
  • Cell protection sits underneath the pack protection. The board watches the individual cells, not only the total pack voltage, so a cell drifting out of line is caught before it drags the rest of the bank with it.
  • Temperature cut-out, not just a warning. Charge and discharge are stopped once the pack leaves its rated window, which matters in a closed locker behind a seat or under a bunk where heat builds quietly through a summer afternoon.
  • Short-circuit protection for installation day. The riskiest hour in the life of any lithium battery is the one where it gets wired in; a dropped spanner or a crossed cable trips the board instead of welding the terminal post.
  • Low self-discharge for the off-season. A pack left in a camper or a boat over winter loses its charge slowly, so the first trip of the season begins with a normal charge rather than a recovery attempt.
  • What the management board does not replace. A correctly rated fuse, cable sized for your load and a properly secured case remain part of the installation — the board protects the cells, not the wiring downstream of the terminals.
Black PA speaker cabinet shown during a live music performance
Certificate of conformity for a lithium ion battery
A large industrial printing press in a factory

Production & Quality Control

  • Cells are graded before assembly. Every cell runs a formation step and a three-cycle capacity test, and cells are sorted by measured capacity so a single weak cell cannot set the life of the whole bank. The cell itself comes off an automated line. Mixing, coating, electrode rolling and slitting, winding, case insertion, tab welding, electrolyte injection and laser welding run in sequence on dedicated machines, which is what keeps joint resistance and dimensional spread consistent from run to run. Every finished unit gets a full outgoing check. Appearance, voltage, capacity, internal resistance and dimensions are measured on 100% of units, not on a sample pulled from the batch. Custom lithium battery runs stay inside the same controls. A changed case length or a different terminal layout moves through the same test sequence as a standard pack; it does not become a one-off outside the quality system. The management system is audited from outside. ISO9001 and ISO14001 management, BSCI compliance and third-party factory audits are what make a repeat order look like the first one.
Quality management system certificate for a lithium-ion battery manufacturer
A certificate of conformity for lithium-ion batteries issued by Anbotek
A stainless steel industrial mixing or processing machine in a cleanroom

Fitting & Installation Checks

  1. Measure the bay, tray or locker against the case dimensions in the specification table, and add room at the terminal end for lugs, a wrench and the cable bend radius.
  2. Check that your cable lugs fit the threaded terminal posts and that the cable gauge suits the load you plan to pull — a pack of this size often goes into wiring that was sized for a much smaller lead-acid block.
  3. Lift the pack in by its case strap, set it down with the terminals facing your cable run, and make sure nothing sharp sits under or behind it.
  4. Secure it properly. A pack that can slide will chafe its own cables and work its terminals loose on the first rough road or choppy crossing.
  5. Connect and check polarity before anything is switched on: positive and negative in the right order, terminals tightened to your own workshop figure, and no stray strands bridging the posts.
  6. Charge it once and watch. A rechargeable lithium battery is only as good as the charger feeding it, so confirm the charger follows the pack's profile and that the management board does not cut out during the first full cycle; note the resting voltage afterwards as your baseline.
Factory production line control station with monitor and yellow perforated rollerClose-up of industrial machinery rollers and gauges on a production lineCleanroom production facility with a worker and a long stainless steel machine with ovalA cleanroom manufacturing production line with a worker and enclosed machinery
24V 100Ah LiFePO4 Battery for RV/Camper, Solar, Marine
White Class C motorhome with mountain landscape side graphics
A white golf cart with brown seats and golf bags in the rear

Applications: RV, Camper, Solar & Marine

A Class C motorhome or a self-build camper van usually carries one house pack for lights, a compressor fridge, a water pump, a fan and device charging — that is the duty this capacity is sized for. Swapping two 12V lead-acid blocks for one rechargeable lithium battery of this size also simplifies the wiring to a single cable pair and removes a pair of batteries that would otherwise age at different rates.

24V 100Ah LiFePO4 Battery for RV/Camper, Solar, Marine

On a roof array above a cabin or workshop, the LiFePO4 battery stores the day's harvest and releases it after dark. Set the solar controller to the pack's lithium profile rather than an inherited lead-acid profile, and size the array against your daily draw rather than against the pack's capacity.

24V 100Ah LiFePO4 Battery for RV/Camper, Solar, Marine

On the water the pack runs a trolling motor, a fish finder, cabin lights, a bilge pump and a radio. There is no liquid electrolyte to spill or top up, but the locker still has to be dry — see the water question further down before you commit a position.

24V 100Ah LiFePO4 Battery for RV/Camper, Solar, Marine

In backup duty the pack keeps UPS units, telecom cabinets, access control and security panels alive between an outage and a generator start. These roles are mostly idle, so what matters is that the pack answers on the first attempt after months of standing.

Golf carts, AGVs, floor scrubbers and light electric vehicles pull hard for short periods — the kind of duty a deep cycle battery is built for, where the surge figure matters as much as the nominal capacity. Emergency and billboard lighting, portable audio systems and garden equipment round out the same 24V pattern.

A cleanroom factory floor with workers operating manufacturing equipment
24V 100Ah LiFePO4 Battery for RV/Camper, Solar, Marine
24V 100Ah LiFePO4 Battery for RV/Camper, Solar, Marine

Specifications

Model No.24V100Ah LiFePO4 Battery (item no. TWE0586)
Nominal Voltage25.6V
Nominal Capacity100Ah, standard discharge @ 0.2C after standard charge
Max Dimensions522 × 238 × 220 mm, customized
WeightApprox. 24 kg
Housing MaterialABS+PC
Terminal TypeM8
Internal Resistance≤40 mΩ
Cycle Life≥2000 cycles, ≥80% of initial capacity
Operation TemperatureCharge 0℃~45℃, discharge -20℃~60℃
Storage at -20℃~25℃Up to 12 months
Storage at -20℃~35℃Up to 3 months
Storage at -20℃~45℃Up to 1 month
24V 100Ah LiFePO4 Battery for RV/Camper, Solar, Marine
24V 100Ah LiFePO4 Battery for RV/Camper, Solar, Marine
24V 100Ah LiFePO4 Battery for RV/Camper, Solar, Marine

Charging & Discharge Ratings

Charge Cut-off Voltage29.2V — the point where charging stops
Standard Charge Current20A, the rate the capacity rating is based on
Max Charge Current100A, the ceiling for a charger or DC-DC feed
Discharge Cut-off Voltage20V — the point where discharge stops
Standard Discharge Current20A, the reference rate for the capacity rating
Max Continuous Discharge Current100A, the sustained load limit
Peak Discharge Current150A for up to 5 seconds, surge only
24V 100Ah LiFePO4 Battery for RV/Camper, Solar, Marine
24V 100Ah LiFePO4 Battery for RV/Camper, Solar, Marine
24V 100Ah LiFePO4 Battery for RV/Camper, Solar, Marine

Ordering & Delivery

  1. Tell us what the pack has to run. Continuous load, surge load, compartment size and the charger or solar controller you plan to use are enough for us to say whether the standard build fits or a custom case is the better answer.
  2. Agree the build drawing. Dimensions on this model are listed as customized, so the final envelope, terminal layout and capacity are fixed on paper before production begins.
  3. Confirm the documents for your destination. Certificate sets and transport paperwork differ by market and by freight mode; ask your sales contact which ones apply to your order and have them itemised on the quotation.
  4. Confirm packing and freight. Sea, air and express each carry their own rules for a lithium battery of this size — give us the delivery address and we will confirm routing, packing and departure point.
  5. Confirm quantity, lead time and price in writing. Scheduling and unit price depend on the build and the volume, so both are quoted for your order rather than published as a fixed figure.
  6. Confirm payment terms and warranty with the quotation. Terms are agreed per order; keep that written confirmation with the packing list so the paperwork matches when the goods arrive.
24V 100Ah LiFePO4 Battery for RV/Camper, Solar, Marine
24V 100Ah LiFePO4 Battery for RV/Camper, Solar, Marine
24V 100Ah LiFePO4 Battery for RV/Camper, Solar, Marine

Scale & Supply Capability

Topwell Power is a lithium battery manufacturer, not a trading house. Our range runs from compact packs to large storage systems, so buyers can consolidate several lines behind one specification standard and one set of shipping documents. OEM and private-label work is routine: your label, case marking, terminal choice, capacity and packing configuration. Capacities and enclosures are customised per project, samples are available before a production run, and shipments go out with the transport documentation freight forwarders ask for. Send your target specification and volume, and we will confirm lead time, packing and pricing for that order.

24V 100Ah LiFePO4 Battery for RV/Camper, Solar, Marine
24V 100Ah LiFePO4 Battery for RV/Camper, Solar, Marine
24V 100Ah LiFePO4 Battery for RV/Camper, Solar, Marine

FAQ

Will this pack replace the lead-acid bank in my camper or boat?

In most camper and marine builds this is the swap people make when a lead-acid set reaches the end of its life, and the real work is in the charger. A 24V LiFePO4 battery holds a higher and flatter voltage than a lead-acid bank, so the charger or solar controller has to be set to the lithium profile, and the compartment has to have room for the case. If you currently run two 12V blocks in series, the wiring simplifies down to a single cable pair.

How do I work out how long 100Ah will run my equipment?

Add up the average current your loads draw at 24V and divide the capacity by that figure — a 100Ah deep cycle battery is rated to deliver 100 amp-hours, so the answer is 100 divided by your average current in amps. Compressor fridges, inverters and trolling motors move that number the most, and an inverter should be counted from its output wattage rather than from the label on its case.

Can I connect two of these in parallel for more capacity?

Parallel connection is a normal way to extend a lithium battery bank, but the packs have to match: same model, same age, same state of charge, and cabling that shares the current evenly between them. Talk to us before you parallel a new pack with one that is already in service, and confirm any series arrangement for a higher system voltage before you wire it.

Can the terminals, cable exit or case size be changed?

The case dimensions are already listed as customized on this model, and terminal type and position form part of the build discussion on any custom lithium battery order. Send the envelope you have to work within and the load you need to connect, and we will confirm what can change without disturbing the pack's ratings.

Is the case sealed against water in a boat locker?

The housing is ABS+PC and there is no liquid electrolyte inside to spill, but this model does not publish an IP rating, so plan for a dry compartment. If the pack has to live in a wet locker, an open cockpit or an exposed tray, tell us where it will sit and we will confirm what protection is available for that position.

What maintenance does it need between trips?

Very little beyond the charger and the terminals. Keep the posts clean and tight, charge before a long lay-up rather than after it, and store the pack within the temperature band printed in the specifications. A rechargeable lithium battery does not need watering, equalising charges or a monthly top-up the way a flooded lead-acid set does, which is the practical reason so many owners make the change.

Brand Introduction

Yichun Topwell Power Co., Ltd (Trademark:TWE) established in 2002, is a high-tech enterprise focusing on the R&D, production and sales of lithium polymer batteries, lithium ion batteries, lithium iron phosphate batteries, and lithium thionyl chloride batteries. Products are widely used in consumer electronics, Internet of Things, smart home, medical, vehicle, home and outdoor energy storage, and have obtained CE, RoHS, Reach, UN38.3, IEC62133, CB, UL, MSDS certifications, etc.

 

Topwell moves on by providing reliable, efficient and intelligent battery solutions to meet different energy needs. We have efficient engineering, production and quality management teams. From raw material procurement, to production, testing, sales and after-sales service, all steps have been controlled by a strict quality management system. Our factory has passed ISO9001, IS014001, BISI certification, SGS, Intertek audit. With the advantages in price, quality and service, we have established long-term and stable cooperative relationships with many well-known brands. Topwell always attached the great importance to the long term cooperation with customers. No matter the order is big or small, we do our best to support you the highest quality with favorable price. We believe that Topwell Power can be your best battery supplier!

Review
Review

ver_code
1/3
X
Send your message to us
ver_code